EPON OLT MODULE | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Date:2018-10-18 14:11:42 | Visits: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1. GENERAL DESCRIPTION This 1490nm DFB EPON OLT SFP transceiver is designed to transmit and receive optical data over single mode optical fiber for link length 20km. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. The transmitter converts 1.25Gbit/s serial CML electrical data into serial optical data compliant with the 10GBASE-LR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor The receiver converts 1.25Gbit/s serial optical data into serial PECL electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
Features
l 1.25Gb/s serial optical interface compliant to 802.3AH specifications small form factor pluggable module “SFP” l 1490 nm DFB transmitter, 1310 nm APD photo-detector BURST receiver l 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers l Operating case temperature: 0 to 70 °C or-40 to 85 °C l All-metal housing for superior EMI performance l Low power consumption l Cost effective OLT solution, l RoHS compliant
Applications
· GEPON networks · FTTX
2. PROPOSED APPLICATION SCHEMATICS
3. PIN DEFINITION
Table 2: OLT SFP Module PIN DefinitionNote: 1. Module ground pins GND are isolated from the module case. 2. Shall be pulled up with 4.7K-10Kohms to a voltage between 3.15V and 3.45V on the host board.
4. TRANSCEIVER BLOCK DIAGRAM
5. ABSOLUTE MAXIMUM RATING These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.
6. RECOMMENDED OPERATING ENVIRONMENTRecommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.
Table 4: Recommended Operating Environment
7. OPTICAL CHARACTERISTICS The following optical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
Notes: 1. Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
2. Power budget is defined as the different between the Rx sensitivity and the Tx output power of the interface.
Table 5: Optical Characteristics
8. DITITAL DIAGNOSTIC FUNCTIONS The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode. For external calibration mode please contact our sales stuff.
9. ELECTRICAL CHARACTERISTICS The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
10. Burst Mode Receiver Dynamic Range
11.Timing Parameter Definitions in Burst Mode Sequence
12. MECHANICAL
Table 10: Key Mechanical Dimensions
13. ESD
This transceiver is specified as ESD threshold 2kV for all electrical input pins, tested per MIL-STD-883, Method 3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are still required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment.
14. LASER SAFTY
This is a Class 1 Laser Product according to IEC 60825-1:1993:+A1:1997+A2:2001. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated (July 26, 2001)
14. Order Information
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Prev:G/EPON 1GE+WIFI ONU (Dual Mode) Next:GPON OLT MODULE |